Industries

Oil & Gas

Gas production, processing and transport depend on continuous processes at remote sites. Data from wells, compressor stations and plants rarely reaches one place in time.

Key processes

  1. Well production
  2. Gathering and treatment
  3. Gas processing
  4. Compression and pipeline transport
  5. Storage and distribution

State programmes and requirements

  • Uzbekneftegaz is discussing distributed control systems, SCADA, PLC and process analyzers with equipment suppliers.

    Source: UzDaily, May 2026
  • An agreement covers the digitalization of gas production processes and the use of artificial intelligence.

    Source: UzDaily, February 2026

Operational challenges

  • Field equipment without remote monitoring
  • Control systems of different generations and suppliers
  • Production decline that needs earlier detection
  • Security of connected control networks

How the solutions work

Each scenario describes how a solution is built for this industry. The scope of a specific project is agreed after a site survey.

03 Industrial Automation

Automation of wellsites and gathering facilities

Wells and gathering points are checked by field crews, so deviations in pressure and flow are seen late.

How it works

  1. Pressure, temperature and flow transmitters at wells and manifolds
  2. RTUs or PLCs with local logic
  3. Radio or cellular link to the control room
  4. SCADA with alarms and production accounting

Systems and protocols

  • RTU and PLC (Modbus, IEC 60870-5-104)
  • SCADA
  • Production accounting

What is delivered

  • Instrumentation and control design
  • RTU and PLC programming
  • SCADA screens and alarms
  • Commissioning

Indicators measured

  • Share of wells monitored remotely
  • Time to detect a deviation
  • Field visits per week
04 Industrial IoT & Edge Computing

Monitoring of compressor and pump stations

Compressors and pumps are the costliest assets on the line, and failures are found when the station trips.

How it works

  1. Vibration, temperature and pressure measurements
  2. Edge processing at the station
  3. Condition indicators and trends
  4. Maintenance planned from the data

Systems and protocols

  • Station control system
  • SCADA
  • Maintenance management system

What is delivered

  • Measurement plan
  • Sensors and edge gateways
  • Monitoring software
  • Alarm rules

Indicators measured

  • Unplanned trips
  • Running hours between repairs
  • Vibration against limits
02 Industrial Software

Integration of production data

Production data sits in control systems of different generations and suppliers and is assembled by hand for reports.

How it works

  1. Data collected from the SCADA and controllers of each site
  2. Data passes to the corporate network through a demilitarized zone
  3. One production data model and historian
  4. Reports and analytics for engineers and management

Systems and protocols

  • SCADA and DCS (OPC UA, OPC DA)
  • Historian
  • ERP

What is delivered

  • Data model
  • Interfaces to each system
  • Historian and reports
  • Documentation

Indicators measured

  • Time to prepare a report
  • Completeness of data by site
  • Manual data entries
08 Industrial Cybersecurity

Segmentation of process control networks

Gas processing and transport control systems are being connected for remote monitoring, which opens paths that must be controlled.

How it works

  1. Inventory of control devices and connections
  2. Zones and conduits with a demilitarized zone
  3. Industrial firewalls and controlled remote access
  4. Monitoring of industrial network traffic

Systems and protocols

  • DCS, SCADA and safety systems
  • Corporate network
  • Remote monitoring links

What is delivered

  • Assessment report
  • Segmentation and access design
  • Configuration of firewalls and remote access
  • Incident procedures and staff training

Indicators measured

  • Connections passing through controlled conduits
  • Remote sessions logged
  • Time to detect unauthorized access
06 Digital Twin & Simulation

Process model of a gas processing unit

Operating changes at processing units are tested in operation rather than on a model.

How it works

  1. Process model built from design data
  2. Calibration with historian data
  3. Scenarios for feed changes and equipment limits
  4. Recommendations reviewed by process engineers

Systems and protocols

  • Historian
  • DCS
  • Laboratory data

What is delivered

  • Calibrated process model
  • Scenario library
  • Training for engineers

Indicators measured

  • Deviation of the model from measured data
  • Scenarios assessed before a change

Next industry